IP Explorer Professional This device replaces your computer based BOOTP/DHCP Server and will quickly assign any IP address to any industrial BOOTP or DHCP enabled control device, like Programmable Controller, PLC communication modules, smart switches and I/O adapters.      Functionality -Detect unknown IP detection -Set IP address -Service DHCP/BOOTP requests -Change static IP address (Target device must comply with Ethernet/IP CIP specification) -Enable Bootp or DHCP to static or dynamic(Target device must comply with Ethernet/IP CIP specification) - 10/100 Full/Half duplex support with autonegotiation - Device info dislpay via Ethernet/IP: Model, Revision, Serial number   Partial list of compatible controllers: - Logix: 1756-ENBT, 1756-EN2T, 1756-EN2TR, 1768-ENBT, 1769-L32E, 1769-L35E - PLC5: 1785-L20E, 1785-L40E, 1785-L80E, 1785-ENET - SLC: 1747-L551, 1747-L552, 1747-L553, SLC 5/05 - Micrologix 1100: 1763-L16AWA, 1763-L16BWA, 1763-L16BBB - Flex I/O: 1788-ENBT, 1794-AENT - Point I/O: 1734-AENT, 1734-AENTR, 1738-AENT - Newtworking: Stratix 6000, 1761-NET-ENI	Troubleshooting Current and Volt Generator Pro $99.95 The Loop Simulator Professional was developed to assist maintenance personnel,  integrators and engineers in analog input testing, troubleshooting and application development. This 3-in-1 device..... - Simulates a 2-wire loop powered transmitter - Provides 4-20mA current source - Provides 2-10V voltage source. Perfect small compact size makes it easy to carry on the job. *More info*	Troubleshooting Current  Generator   The Current Loop Simulator was developed to assist maintenance personnel and integrators in 4-20 mA analog input testing, troubleshooting and application development.  It simulates a 2-wire loop powered transmitter. Five fixed output settings are available: 4 mA, 8 mA, 12 mA, 16 mA or 20 mA.   *More info*   $49.95
Servo Simulator 5 VDC   $54.95 Servo Axis Simulator 5V is the next generation of our servo simulators. This fast 5 Volt version has been developed to assist integrators and OEM in application development for projects with servo drives with analog command signal and incremental encoder feedback. It allows debugging of motion applications in the lab environment, virtually on the table, with PLC or CNC only without actual running motors and drives. It simulates servo axis with servomotor and encoder. Servo Simulator 5V can generate maximum 32,500 pulses per second (130,000 in “A Quad B” or x4 mode). Default encoder settings are 256 pulses per revolution. It effectively provides 1024 positions per revolution if CNC or motion controller uses x4 mode. IMPORTANT: This simulator requires an external 5V /100mA power supply More info click here	USB Servo Simulator $69.95 Servo Axis Simulator USB - the next generation of Servo Simulators was developed to assist integrators in application development for projects with analog servo drives and incremental encoder feedback. It allows motion application debugging in the lab environment, virtually on the table, with PLC or CNC only and without actual running motors and drives. High Speed USB interface helps in parameter customization and live monitoring for multiple axis Servo simulator uses an advanced microcontroller that allows high-speed move simulation and fast response.   Simulator uses USB power from a computer - no external power supply required Simulator can generate maximum 98,000 pulses per second (24.5KHz per each channel). Default encoder settings are 1024 pulses per revolution that can be changed via USB interface. Windows Software is available for download as MSI installer package or Executable file: This link ----> Installer Package is the will create all folders, files and shortcuts.  Unzip and run MSI file.  This link ----> Executable File is the and can be used without installation from any folder   This link ----> Microsoft .Net Framework 3.5 SP1 is the and must be installed on your computer	Servo Simulator 24VDC $69.95 Servo Axis Simulator developed to assist integrators and OEM in application development for projects with servo drives with analog command signal and incremental encoder feedback. It allows debugging of motion applications in the lab environment, virtually on the table, with PLC or CNC only without actual running motors and drives. Servo simulator was originally developed to debug a motion controller project when drives were not available during development. With Servo Simulator motion controller program was developed and tested before actual machine and drives were available. That reduced installation time from weeks to hours. Servo simulator uses advanced microcontroller that allows high-speed move simulation and fast response. It simulates servo axis with servomotor and encoder. Simulator can generate maximum 16250 pulses per second (65000 in “A Quad B” or x4 mode) that is equivalent to about 3800rpm motor. Default encoder settings are 256 pulses per revolution. It effectively provides 1024 positions per revolution if CNC or motion controller uses x4 mode. This device is intended to provide general assistance with application development and debugging and can’t be used in live production systems.   Click HERE for user manual
Encoder Simulator and Tester 5V TTL Differential Line Drive   $99.95 The Encoder Simulator was developed to assist integrators in application development and troubleshooting for projects with High Speed Counters and Flow Meters.  It generates high accuracy square wave signals similar to the incremental encoders and flow meters. This product was designed with ease of use in mind. Simply connect the wires then press the DIR button to toggle between off, clockwise rotation, and counter clockwise rotation and press the FREQ button to toggle between 10Hz, 100Hz, 1KHz, and 10KHz. 5 VDC TTL A, B, and Z. Clockwise and counterclockwise rotation with frequencies of 10Hz, 100Hz, 1KHz, and 10KHz. See here for the manual		Encoder Simulator and Tester 5 to 24VDC Open Collector $99.95 The Encoder Simulator was developed to assist integrators in application development and troubleshooting for projects with High Speed Counters and Flow Meters.  It generates high accuracy square wave signals similar to the incremental encoders and flow meters. This product was designed with ease of use in mind. Simply connect the wires then press the DIR button to toggle between off, clockwise rotation, and counter clockwise rotation and press the FREQ button to toggle between 10Hz, 100Hz, 1KHz, and 10KHz. 5 to 24VDC Open Collector A, B, and Z. Clockwise and counterclockwise rotation with frequencies of 10Hz, 100Hz, 1KHz, and 10KHz. See here for the manual
Industrial USB/RS232/ USB/Serial Adapter Windows 7 Compatible         This is one of our new line of great products.... ((30day money back guarantee and a lifetime replacement guarantee))       Cable length is a proximity 10ft, comes with a mini CD that has procedures and drivers (these can also be downloaded from our website (product support page) the drivers support XP, Vista and Windows 7 (62 or 32 bit)   USB to serial adapter (DB9 male), we have tested on many brands of PLC's (Siemens, Allen Bradley, Automation Direct, Omron, GE and more...)   Please note that you will still need the serial cable for the PLC, this will not take place of that, see our eBay store for the cables, this will convert your USB port to serial and is built for the industrial environment in mind   $29.95	Servo Simulator and Tester Open Collector   $79.95   Servo Axis Simulator developed to assist integrators and OEM in application development for projects with servo drives with analog command signal and incremental encoder feedback. It allows debugging of motion applications in the lab environment, virtually on the table, with PLC or CNC only without actual running motors and drives. It simulates servo axis with servomotor and an open collector encoder. Simulator can generate maximum 16250 pulses per second (65000 in “A Quad B” or x4 mode) that is equivalent to about 3800rpm motor It effectively provides 1024 positions per revolution if CNC or motion controller uses x4 mode	Keyspan USA-HS19 Looking for a way to connect your serial devices to a USB port on your PC The Keyspan High Speed USB Serial Adapter is a simple, inexpensive and reliable way to make this connection.  The Adapter is ideal for use with PLC to laptop programming connections, modems, digital cameras, ISDN terminal adapters, graphics tablets, PDAs, bar code scanners, label printers and other serial devices, which require an RS-232 connection. This High Speed USB Serial Adapter supports data rates up to 230 Kbps---twice the speed of a standard PC serial port. It is 100% USB compliant and features simple "Plug and Pay" installation (no IRQs). Ideal for laptops (it weighs just 2 oz.), the Adapter draws its power from the USB connection so no power adapter is required. This product has received Microsoft XP WHQL certification. Its getting harder to find a laptop with a real serial port, so why bother just use this reliable adaptor. $33.95  (free shipping)
Programming Help and Automation Links	Ind-Concepts LLC 1000 Batesburg Hwy Saluda, SC 29138  (864) 445-2851 email info@plctrainer.net	Product Support and Downloads